| User | Post |
|
February 21, 2011
|
pepage
| | |
| Lifetime Member Expert | posts 119 | |
|
|
If you have a chinese dozer, please post here. Trying to get a current listing of all dozer owners. My dozer is a pre-loader model with steel track, no shuttle clutch and a 2002.5 engine.
|
|
|
February 21, 2011
|
mailman55
| | |
| Lifetime Member | posts 35 | |
|
|
nortrac 3500, blade, steel tracks, 3pth, bought in 2003;
have replaced main clutch, gear changing fork, seals in left steering clutch assembly , and various other minor maintance problems;
leon
|
|
|
February 22, 2011
|
DavidIAM
| | |
| Lifetime Member | posts 32 | |
|
|
Yuchai fiberglass round sexy ??06?? yaller model standard shift backhoe FEL (never used)
box scraper (never used) back blade (never used)
anti-beaver dam damner device.
|
|
|
February 22, 2011
|
Bob Rooks
| | |
| Lifetime Member Platinum Elite | posts 868 | |
|
|
'06 Yuchai YCT306-5A dozer, rubber tracks, manual clutch, Optional FEL equipped.
Original battery, clutch, etc., small radiator repair, and extensive mods and upgrades. Only real issue that I didn't ask for was that it was originally shipped with one of the carrier roller shafts installed bacwards.
Coming up on 600 hours.
|
|
|
February 23, 2011
|
unclebobo
| | |
| Lifetime Member | posts 3 | |
|
|
1996 model Rhino 3060 if I recall correctly.
|
|
|
February 23, 2011
|
Bluenoser
| | |
| Lifetime Member | posts 46 | |
|
|
Steel Track – 306 – 2007 – manual trans (no shuttle shift) – 6 way – loader
Only minor repairs to date.
|
|
|
February 23, 2011
|
kpsp50
| | |
| Lifetime Member | posts 9 | |
|
|
2006 3500c bought 2nd hand orginally from nor trac, manual shift, steel tracks, all original, keep battery maintainer on when not in use. cleared 40 acers runs like new
|
|
|
May 16, 2011
|
LSF
| | |
| Lifetime Member | posts 6 | |
|
|
Post edited 10:59 pm – May 16, 2011 by LSF
2009 Yuchai dozer with FEL steel tracks, skid steer conversion, grapple rake, box blade, 6" chipper, backhoe, wing and a prayer.
|
|
|
November 9, 2011
|
tractorfreak
| | |
| Lifetime Member | posts 30 | |
|
|
2005 Nortrack NT3500C with steel tracks manual shift. I purchased the dozer with 100 hours on it. I have repaired the starter, replaced the voltage regulator, replaced the steering break on the right side, rebuilt the final drive on the right hand side(all bearings, seals and gears), repaired tack. Everything is 100% for now…
|
|
|
November 9, 2011
|
pepage
| | |
| Lifetime Member Expert | posts 119 | |
|
|
Sam,
Where did you get the parts ( bearings, seals and gears) to rebuild your final drive?
Phil
|
|
|
November 9, 2011
|
Little_Grizzly
| | |
| Lifetime Member Expert | posts 184 | |
|
|
Didn't realize this thread was here!
2002.5 engine (non-EPA I think.) Rubber tracks with a spare set of steel tracks. Shuttle clutch, pendulum pedals. Rankin 72" BB30 box blade to boot.
|
|
|
November 10, 2011
|
tractorfreak
| | |
| Lifetime Member | posts 30 | |
|
|
Phil,
I got parts from Circle G tractor and Nortrac. Nortrack did back order some of my spacers but they were good to deal with. They also were good answering questions. The same goes for Circle G.
Sam
|
|
Search 
Home
Print this Topic 
Add a New Topic
Topic RSS 
Recent Comments