- This topic has 15 replies, 5 voices, and was last updated 7 years, 5 months ago by
.
-
Posts
-
-
-
-
-
Once again the book is slammed shut. From the OP’s response, or lack thereof, one can only assume the OP is disgusted with the results from his inquiry.
Well, the OP is a bar near me, doubt they are disgusted or wish to respond to anything on this site. If the OP is me, then I guess my response to you was not read. I assumed that when I responded by email to you, which is how I saw your post, it would be posted on ctoa. Seems that is not the case but I would think that you should have received my email.
-
Once again the book is slammed shut. From the OP’s response, or lack thereof, one can only assume the OP is disgusted with the results from his inquiry.
Well, the OP is a bar near me, doubt they are disgusted or wish to respond to anything on this site. If the OP is me, then I guess my response to you was not read. I assumed that when I responded by email to you, which is how I saw your post, it would be posted on ctoa. Seems that is not the case but I would think that you should have received my email.
I did not receive an email from you. What email address did you send it to?
Account deleted.
-
-
I don’t know what being trolled is, doesn’t sound good. I don’t spend my days on the computer. I responded to an email I received from CTOA assuming because I received the posts, my reply would be posted, if not anyhow you would receive it. If you don’t, I can’t change that, I assume only you can, being it’s your wordpress site? Below is what I replied to you, which you did not receive.
<table class=”Bs nH iY bAt” role=”presentation” cellpadding=”0″>
<tbody>
<tr>
<td class=”Bu yM”></td>
<td class=”Bu bAn”><h2 id=”:156″ class=”hP” tabindex=”-1″ data-thread-perm-id=”thread-f:1611087660992286776″ data-legacy-thread-id=”165bbbb11775d038″>[CTOA Forums] New reply to: “2005 jinma FEL Hyd couplings, Anyone know what the thread is or where to get”</h2><table class=”cf hX” cellpadding=”0″>
<tbody>
<tr class=”hR”>
<td class=”hU hM”>Inbox</td>
<td class=”hV hM”><span class=”hO” tabindex=”0″ title=”Remove label Inbox from this conversation” role=”button” aria-label=”Remove label”>x</span></td>
</tr>
</tbody>
</table>
<table class=”cf gJ” role=”presentation” cellpadding=”0″>
<tbody>
<tr>
<td class=”gF gK”><span class=”gD” data-hovercard-id=”info@ctoa.net”>CTOA</span></td>
<td class=”gF gK”></td>
<td class=”gH bAk”><span id=”:16v” class=”g3″ title=”Sep 8, 2018, 5:28 PM”>Sat, Sep 8, 5:28 PM (3 days ago)</span></td>
</tr>
<tr>
<td class=”gF gK” colspan=”3″>
<table class=”cf iB za ” cellpadding=”0″>
<tbody>
<tr>
<td>DavidPrivett replied: this might work find a metric thread pitch gauge , it will have to be kinda on the larger size and see if you get lucky on it being s stan</td>
</tr>
</tbody>
</table>
</td>
</tr>
</tbody>
</table><table class=”cf gJ” role=”presentation” cellpadding=”0″>
<tbody>
<tr>
<td class=”gF gK”><span class=”gD” data-hovercard-id=”info@ctoa.net” data-hovercard-owner-id=”23″>CTOA</span></td>
<td class=”gF gK”></td>
<td class=”gH bAk”><span id=”:170″ class=”g3″ title=”Sep 8, 2018, 5:54 PM”>Sat, Sep 8, 5:54 PM (3 days ago)</span></td>
</tr>
<tr>
<td class=”gF gK” colspan=”3″>
<table class=”cf iB za ” cellpadding=”0″>
<tbody>
<tr>
<td>Bob Rooks replied: The dash 6 number designates a 3/8″ SAE/JIC fitting with 9/16″ or 5/8″ x 20 tpi. The corresponding metric fitting would have a thread of 18mm</td>
</tr>
</tbody>
</table>
</td>
</tr>
</tbody>
</table><table class=”cf gJ” cellpadding=”0″>
<tbody>
<tr class=”acZ”>
<td class=”gF gK”>
<table class=”cf ix” cellpadding=”0″>
<tbody>
<tr>
<td class=”c2″>
<h3 class=”iw”><span class=”gD” data-hovercard-id=”4dunns@gmail.com”>Pete Dunn</span> <span class=”go”><span aria-hidden=”true”><</span>4dunns@gmail.com<span aria-hidden=”true”>></span></span></h3>
</td>
</tr>
</tbody>
</table>
</td>
<td class=”gH bAk”><span id=”:179″ class=”g3″ title=”Sep 9, 2018, 10:53 AM”>Sun, Sep 9, 10:53 AM (2 days ago)</span></td>
<td class=”gH”></td>
<td class=”gH acX bAm” rowspan=”2″>
</td>
</tr>
<tr class=”acZ xD”>
<td colspan=”3″>
<table class=”cf adz” cellpadding=”0″>
<tbody>
<tr>
<td class=”ady”><span class=”hb”>to <span class=”g2″ dir=”ltr” data-hovercard-id=”info@ctoa.net” data-hovercard-owner-id=”23″>CTOA</span></span></td>
</tr>
</tbody>
</table>
</td>
</tr>
</tbody>
</table><span style=”font-family: inherit; font-size: inherit;”>Rob, repaired a FEL hose that I snapped off on a tree branch. Repaired with one of those emergency repairs, where you screw the outer part over the hose counterclockwise and then the inner section of the coupling clockwise inside the hose. Then a 3/8″ to 1/2″ converter which I have tapped to a thread which is similar to what the </span>jinma<span style=”font-family: inherit; font-size: inherit;”> uses and seems to seal. </span>Eventually<span style=”font-family: inherit; font-size: inherit;”> like to replace this with the correct thread, so I posted asking if anyone knows what the thread really is and where do others get replacement couplings. ( Have replaced HYD cylinders with Magister hyd which are #8 coupling).</span>
<table class=”cf wS” role=”presentation”>
<tbody>
<tr>
<td class=”amq”></td>
<td class=”amr”><span id=”:16r” class=”ams bkH” tabindex=”0″ role=”link”>Reply</span><span id=”:16t” class=”ams bkG” tabindex=”0″ role=”link”>Forward</span></td>
</tr>
</tbody>
</table><span id=”:167″ class=”l8 LJOhwe” tabindex=”0″ role=”link”></span>
</td>
<td class=”Bu yM”></td>
</tr>
</tbody>
</table> -
-
-
Pete,
I’m not sure what size/style your tractor has because Jinma seems to like to change things up without warning.
My 2006 284 front end loader uses European DIN fittings in some places and metric o-ring face fittings in other places.
The dealer I bought the tractor from doesn’t have a clue about hydraulic hoses and fittings so I had to go searching on my own. Caterpillar dealers can get some of the DIN fittings and custom make hoses with different ends. When I worked there, they had nothing in the metric o-ring fittings. However, you can find some adapters to go to JIC fittings. This is expensive, but at least you can get hoses with JIC ends made just about anywhere.
Here is a hydraulic fitting guide from http://www.discounthydraulics.com
If you can post pictures of your fittings and maybe measure them using this guide maybe we can figure out what you have and what you need.
-
-
If the cylinders fittings are welded in they will need to be dissembled to be cut out and new one’s welded in I would think (heat and hydro seals do not mix) . But if you have access to a machine shop adapters should be able to be made to convert what ever to what ever. But I have not had a lot of luck finding people with skills and or time to do small things like that around here.
-
I agree with David.
Strip down your cylinders and take them to a welding shop along with the fittings you want to use, but then you will still have to buy two new JIC hoses per cylinder PLUS one adapter for each hose. Or just buy the metric ORFS to JIC adapters for around $30 each (two per new JIC hose). It would be an expensive process to reinvent the wheel and change over all the fittings to JIC. Your best bet is to accept what you have and use the appropriate fittings. ORFS fittings are used world wide and very popular on heavy equipment.
Select your size from this chart –
https://www.discounthydraulichose.com/Male_JIC_x_Female_Metric_Face_Seal_Solid_p/9022fc.htm
Account deleted.
-
-
-
- You must be logged in to reply to this topic.